linersense.blogg.se - Cutting vinyl lattice panels

#Cutting vinyl lattice panels how to#
#Cutting vinyl lattice panels free#

You can also use it as brackets and as other trim pieces too. Use vinyl panels to create lots of curb appeal as running trim between columns. Whether used on residential homes or businesses, vinyl lattice offers so many more options than wood and does not require any maintenance. Vinyl lattice trim can be custom designed and painted any color to complement your home's colors. Then use our convenient directory below to find your favorite use for this product. Mary and I know you will be inspired by watching our short video showing you a few ideas for using these lattice panels. Lattice deck railings offer privacy as well

#Cutting vinyl lattice panels how to#

We recommend you research " How To Paint PVC or Vinyl" on the internet prior to purchase if your goal is to repaint the PVC.ĭecorative designs afford you maximum appealĬhoose from a variety of patterns or design your own If there's a large gap beneath the panel, add soil, then smooth it out to create a consistent space between the panel and ground.Vinyl or PVC can be painted however, it may require additional preparation and/or special paint (like Fusion for Plastic® from Krylon) If it drags on the ground, use a shovel or rake to remove some dirt from in front of the panel.

Check to make sure the panel swings up and down smoothly.

Use a drill/driver to screw the hinge to the porch. Slip a pry bar under the panel and raise it up tight against the porch fascia.

Screw the hinges to the frames first, then set the panels in the openings under the porch.

Two hinges are sufficient for a panel that's shorter than 8 feet, but use three hinges on one that's longer.

Hang the framed-lattice panels from the porch with either 3- or 4-inch strap or T-hinges.

Hang the framed-lattice panels Photo by Chip Henderson

Where two pieces of vinyl lattice meet at a center stile, secure the seam with two rows of 1-inch panhead screws.Ħ.

Be sure to drill clearance holes slightly larger than the screw shanks so the lattice can expand and contract.ĥ. Lay the frames facedown and attach the lattice with 1-inch panhead screws driven through washers.

Cut the lattice panels down to size using a sabre saw or circular saw.

Size the lattice panels Photo by Chip Henderson

Once the frames are assembled, apply a coat of primer, followed by two coats of gloss enamel trim paint.Ĥ.

Be sure the leg of the T-shaped plate is centered on the 1x4 stile.

Connect the center stile to the frame with two 4-inch T-plates.

Connect the center stile, prime, and paint Photo by Chip Henderson

Position the hardware pieces about ¼ of an inch from the edge of the frame and secure them with 3/4-inch-long flathead screwsģ.

Strengthen the frame by installing a 6-inch mending plate and a 3½-inch flat corner brace at each corner joint.

Cut the frame parts to length and assemble them facedown on a flat surface.

The completed frames must be a ½-inch narrower than the overall width and 1 inch shorter than the height.Ģ. Measure the openings between the columns or posts.Be careful that you don't damage the porch fascia or support columns. Start by removing the old lattice from the porch with a flat pry bar.Prep for installation Photo by Chip Henderson

The techniques used here can also be adapted for replacing lattice on a deck, fence, gate, privacy screen, or trellis. The swing-up frames also make it easy to crawl underneath the porch to repair the framing if needed. Rather than permanently attach the frames, we hung them on hinges so the homeowners could use the space below the porch for storage. We also opted for an unconventional installation method. Here we built a durable new skirt using pressure-treated lumber and TuffBilt plastic lattice. (The porch we worked on had this type of skirt.) While a frameless skirt is easy to install, it's also susceptible to warping and damage because the lattice has very little support. Occasionally, a porch skirting doesn't have a framework and simply consists of a lattice screen attached directly to cleats nailed to the understructure framing. In regions that receive a lot of precipitation, wood rot can begin to appear in less than two years. In time, the parts closest to the ground begin to rot and the decay spreads to the lattice. In older homes, it's often built of untreated pine or fir, neither of which is very resistant to decay and bugs.

#Cutting vinyl lattice panels free#

This enclosure conceals the framing while it also allows air to circulate under the porch floor, which keeps the framing dry and free of rot.Ī skirt typically consists of a lattice panel set into a wood frame. Here you'll learn how to handle one of the most common of all porch repairs: building a new lattice skirt. If your porch isn't well maintained, the whole house looks shabby.